R11815 WATER BATH PRODUCTION UNIT

SEPARATOR, HORIZONTAL, either 24" O.D. x 7’ 6” (Head Seam to Head Seam), 1000 psig Working Pressure, 1300 psig Test Pressure, 3‑Phase. To include Internal Oil and Water Boxes. To be repaired in accordance with Section VIII, Division 1, of the ASME Code.

Accessories ‑ Components:
• 1 - 3” 600 # RFWN gas inlet connection with internal inlet assembly, swaged to 2” NPT
• 1 - 4” 600# RFWN gas outlet connection, swaged to 2” NPT
• 1 - 1 Wire mesh type mist extractor, 4" thick, 304 stainless steel wire mesh
• 2- Liquid level controllers, refurbished, non-bleed, 4" hammer union connection, snap acting, integral sight glass assembly, Norriseal
• 1 - Oil discharge valve, refurbished, Kimray Model 2200, ¾” standard trim
• 1 - Water discharge valve, refurbished, Kimray Model 2200, ¾” standard trim, Kimray Model 180-SMS
• 1 - Pressure gauge, new, 0‑1000 psi range, 2 ½” face, stainless steel internals, with new isolation valve
• 1 - Thermometer, new, installed in separator liquid section, 20‑240 Deg. F. range, with carbon steel thermowell
• 1 - Thermostat installed in separator liquid section, refurbished, Kimray T12, with carbon steel thermowell
• 1 - 1” Relief valve, new, set at 1000 psi, with riser pipe and rain cap
• 1 - 1” Safety head assembly, refurbished, with new rupture disc, riser pipe and rain cap
• 1 - 2" Drain connection with pipe plug
• 1 - Adjustable water siphon

Liquid section of separator is built immersed in heater water bath area to prevent freeze‑ups.


INDIRECT HEATER:
Approximately 30” wide x 3’-0” high x 7’-10” long

Accessories – Components:
• 1 - Firebox, 10 ¾” O.D., U‑tube, 500,000 Btu/Hr. nominal capacity
• 1 - Smokestack, refurbished, 10" O.D. x 10'‑0" high, with flanged connection and new bird screen
• 1 - Flame arrestor, horizontal, with flame cell 1” Eclipse type burner, pilot light, and 6" access opening with cover. 
• 1 - Wellstream heating coil, refurbished, removable, 3” XH seamless pipe, 3000 psig W.P., minimum of 4 – tube, 18.65 square feet heat transfer area
• 1 - Thermostat, refurbished, Kimray T‑12, with carbon steel thermowell
• 1 - Thermometer, new, 20 ‑ 240 Deg. F. range, with carbon steel thermowell
• 1 - Supply gas preheat coil, refurbished, ½” XH Smls. Pipe
• 1 - 2” Fill cap assembly, refurbished
• 1 - 2" Drain connection with pipe plug


PRESSURE CONTROL ASSEMBLY:
• 1 - 2” Control valve installed at inlet to separator, refurbished, 1” standard trim, 4000# carbon steel body, Kimray Model 2400-SMT-PO with 23-MVP manual valve positioner
• 1 - Pressure controller, Refurbished, 0-1000 psig stainless steel bourdon tube, Ametek
• 1 - Mounting assembly for pressure controller
• 1 - ¼” Needle valve, new, installed in the sensing tubing line to the pressure controller
• 1 - Instrument gas filter regulator, new, Fisher Type 67CFR


SUPPLY GAS AND INSTRUMENT GAS SYSTEM:
• 1 - Supply gas drier, 2 3/8” O.D. x 3'‑0" high, new or refurbished, installed on the gas outlet piping
• 1 - Supply gas shut‑off valve, new, ½” carbon steel ball type
• 1 - Safety supply gas scrubber, 6” O.D. x 24” high, non-code, capped ends, with new drain valve and new Mercer type relief valve, set at 125 psi
• 1 - Supply gas regulator, refurbished, Fisher Type 627-118
• 1 - Supply gas pressure gauge, new, 0-200 psig range, stainless steel internals
• 1 - Burner fuel gas regulator, refurbished, Fisher Type 64-27
• 1 - Burner fuel gas pressure gauge, new, 0-30 psig range, stainless steel internals
• 1 - Burner fuel gas shut‑off valve, new, ½” carbon steel ball type, Balon or equal
• 1 - Burner fuel gas control valve, refurbished, Fisher Type 119
• 1 - Pilot light fuel gas regulator, new, Fisher Type 67CR
• 1 - Pilot light fuel gas pressure gauge, new, 0-30 psig range, stainless steel internals
• 1 - Pilot light fuel gas shut‑off valve, new, ¼” carbon steel ball type, Balon or equal
• 1 - Instrument gas regulators, new, Fisher Type 67CR
• 1 - Instrument gas shut-off valves, new, ¼” carbon steel ball type, Balon or equal
• 1 - Set of burner and temperature controller piping and tubing. Tubing and tube fittings to be new 3/8” stainless steel.


INSULATION, SKID & SKID ASSEMBLY:
1 - Structural steel skid refurbished, with loading accommodations at ends, 6" channel runners and 2 7/8" O.D. pipe ends.