R11816 Vertical Separator

Vertical Separator, Refurbished, 16” O.D. x 5'‑6" High (Head Seam to Head Seam), 2-Phase, 680 psig Working Pressure.  Designed and constructed in accordance with Section VIII, Division 1, of the ASME Code with the ASME Code Stamp applied and registered with the National Board of Boiler and Pressure Vessel Inspectors.

Accessories ‑ Components:

 1 ‑   1" Bottom drain assembly with pipe plug

 1 ‑   Internal deflector assembly

 1 ‑   Quieting assembly for liquid level controller

 1 ‑   Mist extractor assembly installed in upper section of separator, 4" thick high-density wire mesh, 304 SST

 1 -   3” down comer with 2” gas drier connection

 1 ‑   3” 300 ANSI Flanged inlet assembly

 1 ‑   3” 300 ANSI Flanged gas outlet assembly

 1 ‑   Liquid level controller, refurbished, with 2" hammer union connection, snap acting,  Norriseal Series 1001

 1 ‑   2” Liquid discharge valve, refurbished, 1” standard trim, Kimray Model 2200-SMT-PO

 1 -   2” Ball valve, installed upstream of above liquid discharge valve, regular port, Balon 2R- 

         F93-SE 

 1 ‑    Pressure gauge, 0‑1000 psig range, stainless steel internals, with isolation valve

 1 ‑   Relief valve, 1", set at 740 psig, with riser pipe and rain cap

 

Indirect Heater

Indirect Heater, Refurbished, Approximately 3'‑6" Long x 1'‑0" Wide x 3'‑6" High


Accessories ‑ Components:

 1 ‑   Firebox, refurbished, integral, 6 5/8" O.D. U‑tube, 125,000 Btu/Hr. nominal capacity, 15 Sq. Ft. heat transfer area

 1 ‑   Smokestack, refurbished, 6" O.D. x 10'‑0" long, flanged connection, with bird screen

 1 ‑   Flame arrestor, refurbished, horizontal, 14" diameter flame cell, to include burner, pilot light and 6" access opening with cover

 1 ‑   Thermostat, refurbished, Kimray T‑12, with carbon steel thermowell

 1 ‑   Thermometer, 20‑240 Deg. F. range with carbon steel thermowell

 1 ‑   Supply gas preheat coil, 1” XH Smls. Pipe

 1 -   Tubular sight glass assembly with bronze gauge valve, tubular gauge glass and guard rods

 1 ‑   Fill cap assembly

 1 ‑   Drain connection, 1", with pipe plug

 

Supply Gas and Instrument Gas System

 1 ‑   Supply gas drier, refurbished, 2 3/8" O.D. x 3'‑0" high, 1000 psig W.P.

 1 ‑   Supply gas shut‑off valve, ½”

 1 ‑   Safety supply gas drip pot, refurbished, 3 ½” O.D. x 1'‑0" high, 125 psig W.P., with drain valve and carbon steel relief valve.  Relief valve to be piped outside of enclosure

 1 ‑   Supply gas regulator, Meco Type P125

 1 ‑   Supply gas pressure gauge, 0-200 psig range, stainless steel internals

 1 ‑   Instrument gas regulator, Fisher Type 67CR

 1 ‑   Instrument gas shut‑off valve, carbon steel ball type

 1 ‑   Burner fuel gas regulator, Fisher Type 67CR

 1 ‑   Burner fuel gas pressure gauge, 0-30 psig range, stainless steel internals

 1 ‑   Burner fuel gas shut‑off valve, carbon steel ball type

 1 ‑   Burner fuel gas control valve, Kimray 3PG

 1 ‑   Pilot light fuel gas regulator, Fisher Type 67CR

 1 ‑   Pilot light fuel gas pressure gauge, 0-30 psig range, stainless steel internals

 1 ‑   Pilot light fuel gas shut‑off valve, carbon steel ball type

 

Enclosure, Skid and Skid Assembly

 1 -   Enclosure, refurbished, 4’-0” wide x 4'-0" long x 4'-0" high, steel, non-insulated, with 1-hinged doors.  Door is provided with positive type, easily operated latche that may be secured with padlock.  Encloses level controller, dump valve, drip pot, regulators, etc.

 1 ‑   Structural steel skid on bottom of unit, refurbished, 4" channel runners

 1 ‑   Set of supply gas, instrument and fuel gas piping and tubing.  Tubing and tube fittings to be 3/8” stainless steel.

 1 ‑   Paint job of above to consist of coat primer paint and coat Fed. Spec. paint.