R13164 Host Treating Type Production Unit

Separator, 12 3/4" O.D. x 7'‑6" Long (Head Seam to Head Seam), 720 psig Working Pressure, 1000 psig Test Pressure, Horizontal, 2‑Phase with 10 3/4" O.D. x 3'‑0" Long Liquid Sump that is immersed in liquid section of Separator‑Treater.  Repaired in accordance with ASME Code Section VIII, Division 1, with “R” Code Stamp applied. 
 
 Accessories - Components:
 1 ‑   Mist extractor, 12" Dia. x 4" thick, 304 stainless steel, high density
 1 -   2" Inlet connection with inlet diverter
 1 ‑  Liquid level control, with 4" hammer union connection, with sight glass, snap    
       acting,  refurbished Norrieseal 1001 or equal
 1 ‑   Instrument gas regulator, new,  Fisher Type 67R
 1 ‑   No‑freeze liquid discharge valve, refurbished Kimray 180‑SMS, 3/8" trim
 1 ‑   Pressure gauge, new, 0-1500 psig range, stainless steel internals, with
        isolating valve
 1 ‑   1" Safety relief valve, new, set at 1000 psig, with riser pipe and rain cap
 1 ‑   1" 3000# Union type safety head assembly, refurbished with new rupture disc,
        riser pipe and rain cap
 1 ‑   Thermometer with carbon steel thermowell, new
 1 ‑   Supply gas drier, refurbished, 2 3/8" O.D. x 3'‑0" high, 1000# W.P. 
 1 ‑   Supply gas shut‑off valve, new, carbon steel ball type
 1 ‑   Liquid section of separator immersed in liquid section of separator‑treater to prevent freeze‑ups
 1 ‑   1 1/2" Bottom drain connection with 1” drain valve
 
Separator‑Treater
Horizontal Oil‑Water‑Gas Separator‑Treater, 24" O.D. x 10'‑0" Long, 250 psig Working Pressure, 325 psig Test Pressure. ASME Code Stamped per ASME Section VIII and registered with the National Board of Boiler and Pressure Vessel Inspectors.
 
 Accessories – Components:
 1 ‑  Firebox, integral, 6 5/8" O.D. pipe U‑tube, 19.4 Sq. Ft. heat transfer area,
       125,000 Btu/Hr. Nominal Capacity.  Includes 1 1/2" lighting connection with  
       cap 
 1 ‑  Flame arrestor, refurbished, 10 ¾” Dia., horizontal, to include burner, pilot light, and 6” access opening with cover.
 1 ‑   Smokestack, 6" O.D. x 10'‑0" long, with down draft diverter and bird screen
 1 ‑   Supply gas preheat coil
 1 ‑   Supply gas shut‑off valve, new, steel ball type
 1 ‑   Safety supply gas scrubber, 4 ½” O.D. x 2'‑0" high, 125# W.P., to include high liquid level shutdown, drain valve and relief valve
 1 ‑   Supply gas regulator, refurbished Fisher Type 627-118
 1 ‑   Supply gas pressure gauge, new, 0-200 psig range, stainless internals
 1 ‑   Set of burner and temperature controller piping
 1 ‑   Burner fuel gas regulator, refurbished Fisher Type 67CR
 1 -   Burner fuel gas control valve, refurbished Fisher Type 119
 1 ‑   Burner fuel gas pressure gauge, 0-30 psig range, stainless internals
 1 ‑   Burner fuel gas shut‑off valve, new, ball type
 1 ‑   Temperature controller, refurbished, Kimray T12, with carbon steel
        thermowell
 1 ‑   Pilot light fuel gas regulator, refurbished Fisher Type 67D-27
 1 ‑   Pilot light fuel gas shut‑off valve, new, ¼” ball type
 1 ‑   Pilot light fuel gas pressure gauge, new, 0-30 psig range, stainless internals
 1 ‑   Thermometer, new, 3" dial face, 20‑240 Deg. F. range, with carbon steel
        thermowell
 2 ‑   Liquid level controllers, 4" hammer union connection, snap acting, refurbished Wellmark Model ST4UP       
 2 ‑   2" Pilot operated liquid dump valves, refurbished, Kimray Model
       240‑SMA‑PO with 2” new ball valves for isolation in front of dump valves,
       Balon type 2R-S32-SE
 1 ‑  Instrument gas regulator, new, Fisher Type 67CR
 1 ‑  Pressure gauge, new, 0-200 psig range, stainless internals, with shut‑off valve,
       ¼” Balon
 2 ‑   Instrument gas shut‑off valves, ¼” carbon steel ball type
 2 ‑   Tubular gauge glass assemblies, new, complete with brass valves, tubular
        gauge glass and guard rods
 1 ‑   2" Relief valve, new, set at 250 psig, with riser pipe and rain cap
 1 ‑   2" Gas back pressure regulator, refurbished Kimray 230‑SGT‑BP
 1 ‑   1 1/2" 3000# Union type safety head with rupture, riser pipe and rain cap
 1 ‑   Water siphon assembly, internally adjustable
 1 ‑   1" Internal piping to conduct liquid from discharge of high pressure separator to inlet of separator‑treater
 1 ‑   2" Connection with pipe plug ‑‑‑ for auxiliary inlet
 2 ‑   2" Drain connections on vessel, with pipe plugs
 2 ‑   1/2" Drain connections on oil and water boxes, with pipe plugs
 
Skid & Skid Assembly
 1 ‑   Structural steel skid, 6" channel runners, with loading accommodations at both ends
 1 ‑   Set of supply gas, instrument gas and fuel gas piping and tubing.  Tubing and tube fittings to be stainless steel 
 1 ‑   Set of 1" piping to connect outlet of dump valve on high pressure separator to inlet of liquid conductor pipe in separator‑treater
 1 ‑   Paint job of above, to consist of coat primer paint and coat Fed. Spec. paint